SW series solar controller
► Wireless remote control design, remote control parameters can be modified through handheld devices; ► Full digital high-precision chip control, high conversion efficiency up to 97%; ► 4 period + morning light adjustment function, users can set the working current of the LED; ► With open circuit, short circuit, reverse connection, wrong connection protection; ► With overcharge, overdischarge, overload, temperature protection function and temperature compensation function; ► Optional charging mode, with activation function (only applicable to lithium controller) ► With automatic power reduction function, can automatically adjust the output according to the battery power, extend the lighting time; ► With cyclic output, pure light control, pure time control, normal open, light control + time control, a variety of working modes ► Intelligent timing design, set the time period when the load is open, easy to install lithium battery engineering. ► Intelligent timing design, in the case of load open circuit, set the period of time is not timed, easy to install lithium battery street lamp project. ► Suitable for 3 series, 4 series lithium battery (lithium battery type)
Classification:
Wind & solar hybrid controller
Hotline:
SW series solar controller
Waterproof constant pressure integrated solar charging controller - Power adjustable
model: PT122408
Waterproof constant pressure integrated solar charging controller - Power adjustable model: PT122408

Wiring attention
1. The wiring sequence is from right to left. At the same time, use insulation tape to tighten each wire to avoid short circuit caused by wires touching together.
2. first connected to the load, then connected to the battery, at this time the battery light is on, wait 10 seconds, the load starts to work, while the load indicator light;
3. after the solar panel, at this time the load is off, while the solar light blinking slowly, the battery light is on, the load light is off, the charging is normal, and the wiring is completed.
Automatic power reduction
When the low-voltage automatic energy saving function is turned on, the controller will enter the automatic energy saving mode. When the battery voltage is lower than the low-voltage protection voltage, the controller will automatically calculate the output power of the load according to the battery voltage. The pre-set controller working time and power will not change, and the controller will compare the output power calculated by the control itself according to the pre-set output power. Take the smaller value output, for example, when the pre-set output is 10W, the controller calculated output is 8W, then the actual output is 8W; When the pre-set is 8W and the output calculated by the controller is 10W, the actual output is still 8W.
Input-output characteristic
1.large output current: 10A
2.large charging current: 10A
3.large output power: 12V 120W/24V 240W
Working mode
The working time of the controller is divided into 4 periods + morning light, and each working time and power are adjustable.
1, light control + time control: after the light is on at night, it runs successively according to the working time and power, and automatically turns off the light after reaching the light control voltage or setting the time period after the operation is completed;
2, delay lighting mode: you can set the light control delay or set the time period to 0 to achieve the delay lighting;
3, morning bright mode: the controller automatically calculates the night length according to the light control time, and intelligently adjusts the morning bright spot, thus making the morning bright time more accurate;
4, normally open mode: to meet special needs, the controller is not controlled by light control;
Parameter reading and modification
Through the remote control, you can set the voltage parameters, load current, working mode, working time and working power of the controller, and read whether the parameters currently set by the controller are correct.
Basic parameters of the controller
| parameter | numerical value | adjustable type | default | default |
| system voltage | 12V system | colloid | lithium electrode | |
| Large charging current | 8A | |||
| Large voltage solar panel | ≤27V | |||
| Overcharge protection voltage | 9-17V;×2/24V | √ | 14.5 | 12.5 |
| Equal charge protection voltage | 9-17V;×2/24V | √ | 14.3 | 12.2 |
| Overcharge recovery voltage | 9-17V;×2/24V | √ | 14.0 | 12.0 |
| Floating charge protection voltage | 9-17V;×2/24V | √ | 13.8 | 12.0 |
| Over-discharge recovery voltage | 9-17V;×2/24V | √ | 12.0 | 10.2 |
| Over-discharge protection voltage | 9-17V;×2/24V | √ | 10.8 | 9.0 |
| temperature compensation | —4.0mV/℃/2V | |||
| Overtemperature protection value | 60℃ | |||
| Optically controlled voltage | 5V~11V | √ | 5V | |
| Optically controlled delay | 0~50min | √ | 0min | |
| operating temperature range | —35℃~60℃ | |||
| protection level | IP67 | |||
| static dissipation | ≤20mA | |||
| conversion efficiency | ≥ 96% | |||
| overall dimension | 81*68*196mm | |||
| installation size | 76*44mm | |||
| Installation aperture | 3mm |
Next
Previous
None
Next
Manual Download
Related Products
Consult Immediately
If you are interested in our products, please leave your email and we will contact you as soon as possible. Thank you!
CONTACT US
Contact Us
Contact Phone:
Company E-mail:
Company Address:
Max Science Park 1201, Tianshi Road, Shushan District, Hefei City
Product Advisory 1
Product Advisory 2